Front | Camber Adjusting Bolt Kit
| SPF4351-12K | 1 | | $53.00 |
Kit, camber adjustmentCamber Adjusting Bolt KitCamber Bolt Kit 12mm Vehicle Application Information: - adds +/- 1.5 degrees camber
- Fitting Position: Front
- Fitting time [min]: 60
- Part of kit: (x)
|
Front | Control Arm Lower Assembly Kit
| TRC1142 | 1 | | $409.00 |
Control/Trailing Arm, wheel suspensionControl Arm Lower Assembly KitVehicle Application Information: - includes left and right arms and all bushes
Left and Right Arms for Standard Replacement and Repair Upgrade The SuperPro front lower control arm kit has been designed to be an easy repair solution. Offering both alignment and vehicle handling improvements. Designed not just as a repair solution but as an upgrade! Supplied as a complete kit and fully assembled with special uprated ball joints and proprietary SuperPro bushings. We have made this kit by far the best choice on the market. These arms utilise the SuperPro bushings and are manufactured from a high strength material. By eliminating the O.E style rubber bushing, these arms have been optimised for longevity, durability and performance, without any unwanted NVH. SuperPro Control Arms are perfectly suited as a standard replacement and are an upgrade from the factory arms, eliminating the undesirable arm movement to maintain better steering geometry in all driving conditions.
SuperPro Tip - SuperPro strongly advises that both arms should always be replaced at the same time to maintain the correct geometry and operation of the vehicle.Vehicle Application Information: - standard replacement
- Includes Ball Joint
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Fitting time [min]: 60
- Part of kit: (x)
|
Front | Control Arm Lower Front Bush Kit
| SPF2477K | 1 | | $102.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower Front Bush KitVehicle Application Information: - Fitting time [min]: 210
- Fitting Difficulty: difficult
- Fitting Position: Front
- Axle alignment required after fitting
- Part of kit: (x)
|
Front | Control Arm Lower Rear Bush Kit
| SPF2478K | 1 | | $210.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower Rear Bush KitVehicle Application Information: - Fitting time [min]: 210
- Fitting Difficulty: difficult
- Axle alignment required after fitting
- Fitting Position: Front
- Part of kit: (x)
|
Front | Control Arm Lower Rear Bush Kit - Double Offset
| SPF2480K | 1 | | $148.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower Rear Bush Kit - Double OffsetVehicle Application Information: - 1 degree caster adjustment available
A Double Offset kit is used for enhanced handling performance and will deliver positive caster to both sides of the vehicle. The vehicle will have improved directional stability, crisper, more responsive steering and improved 'return to centre' feel. This is a non tyre wearing geometry change that has a substantial effect on a vehicles handling characteristics.
Follow the installation instructions and enjoy the results! Vehicle Application Information: - Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting time [min]: 210
- Fitting Position: Front
- Part of kit: (x)
|
Front | Control Arm Lower-Rear Bush Kit - Single Offset
| SPF2479K | 1 | | $148.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower-Rear Bush Kit - Single OffsetVehicle Application Information: - There must be at least 30mm of clearance between the droop stop and the chassis at ride height to avoid any damage to the arms.
Use this kit to rectify a steering pull after a vehicle has been aligned to the manufacturer's specifications. Supplied with an offset bush to be fitted to the passenger side and a standard bush for the driver's side, these kits stagger the caster or setback by repositioning the ball joint slightly forward in the chassis. This is a non tyre wearing geometry change that has a substantial effect on a vehicles ability to track straight and other handling characteristics. Follow the installation instructions and the problem is solved. Vehicle Application Information: - alignment correction
- Steering Pull Correction Kit
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting time [min]: 210
- Fitting Position: Front
- Part of kit: (x)
|
Front | Steering Rack & Pinion Mount Bush Kit (Passenger Side)
| SPF3560K | 1 | | $45.00 |
Bush, steering shaftSteering Rack & Pinion Mount Bush Kit (Passenger Side)- Fitting Difficulty: difficult
- Axle alignment required after fitting
- Fitting time [min]: 180
- Fitting Position: Front
- Part of kit: (x)
|
Front | Sway Bar Link
| TRC4037 | 2 | | $47.00 |
Stabiliser Bar, suspensionSway Bar Link10mm Ball Joint/Bush Link
Length 85mm center to center Vehicle Application Information: - Fitting time [min]: 30
- Fitting Position: Front
- Fitting Difficulty: moderate
- Part of kit: (x)
|
Rear | Beam Axle Pivot Bush Kit
| SPF1942-90K | 1 | | $139.00 |
Bush, beam axleBeam Axle Pivot Bush KitVehicle Application Information: - Track Kit
- don't remove original shell
- Axle alignment required after fitting
- Fitting Position: Rear
- Fitting Difficulty: difficult
- Fitting time [min]: 240
- Part of kit: (x)
|
Rear | Beam Axle Pivot Bush Kit
| SPF1942K | 1 | | $146.00 |
Bush, beam axleBeam Axle Pivot Bush KitVehicle Application Information: - don't remove original shell
- Axle alignment required after fitting
- Fitting time [min]: 240
- Fitting Difficulty: difficult
- Fitting Position: Rear
- Part of kit: (x)
|
Rear | Panhard Rod Bush Kit
| SPF4191K | 1 | | $95.00 |
Bush, panhard rodPanhard Rod Bush Kit- Fitting Position: Rear
- Part of kit: (x)
|
Rear | Suspension Link Bush Kit
| SPF4189K | 1 | | $66.00 |
HandlebarsSuspension Link Bush Kit- Fitting Position: Rear
- Part of kit: (x)
|