| Front | 33mm Heavy Duty 2 Point Adjustable Sway Bar
| RC0121FZ-33 | 1 |  | $478.00 |
Stabiliser Bar, suspension33mm Heavy Duty 2 Point Adjustable Sway BarIf you are looking for increased cornering capabilities with decreased body roll, Roll Control sway bars are the answer!
By being adjustable the Sway bar rates can be increased between 30-50% over OE sway bars by simply changing the end link position on the sway bar.
- Axle alignment required after fitting
- Fitting Position: Front
- Fitting time [min]: 120
- Fitting Difficulty: difficult
- Part of kit: (x)
|
| Front | Control Arm Lower Bush Kit
| SPF5479K | 1 |  | $453.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower Bush KitControl arm bushes stabilise the movement of the arms to ensure the correct geometry is maintained in all situations.
Worn or rubber bushes in these locations lead to dynamic changes in wheel alignment that effect the handling of a vehicle as well as the tyre life.
SuperPro Bushings solve this issue and are the perfect repair or repair upgrade solution. Vehicle Application Information: - Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting time [min]: 180
- Fitting Position: Front
- Part of kit: (x)
|
| Front | Control Arm Replacement Ball Joint for Fixed Offset Control Arm
| KIT6490RK | 1 | | $107.00 |
Ball Joint Repair KitControl Arm Replacement Ball Joint for Fixed Offset Control ArmThis kit contains one replacement heavy-duty high-articulation ball joint for the SuperPro fixed offset Upper control arm. The kit contains a brand-new ball joint, which also includes a new dust boot, circlip, nut and any other required installation hardware.
Notes: If both ball joints need replacing, two kits will be required.
This kit is used to replace the ball joint in the following part numbers: TRC6490, TRC6690
Vehicle Application Information: - replacement Ball Joint to suit TRC6490 & TRC6690 only
- Fitting Position: Front
- Fitting Difficulty: difficult
- Fitting time [min]: 60
- Part of kit: (x)
|
| Front | Control Arm Replacement Bush Kit for Fixed Offset Control Arm
| KIT6690K | 1 | | $47.00 |
Mounting Kit, control/trailing arm mountingControl Arm Replacement Bush Kit for Fixed Offset Control ArmThis kit contains two replacement SuperPro polyurethane bushings for the SuperPro fixed offset upper control arm.
The replacement kit contains new bushings, crush tubes, a tube of grease and any other required hardware such as washers.
Note: Two kits will be required if the bushings in both arms need replacing.
This kit is used to replace the bushings in the following part numbers: TRC6690
Vehicle Application Information: - replacement bush kit to suit TRC6690
- Axle alignment required after fitting
- Fitting Position: Front
- Fitting Difficulty: difficult
- Fitting time [min]: 120
- Part of kit: (x)
|
| Front | Control Arm Upper Complete Assembly - Fixed Offset
| TRC6690 | 1 | | $658.00 |
 Control/Trailing Arm, wheel suspensionControl Arm Upper Complete Assembly - Fixed OffsetVehicle Application Information: - providing an increase of 1 degree of caster and 0.5 degrees of negative camber over the OE UCA
Left and Right Fixed Offset Arms for Lifted Vehicles with Caster and Camber Correction fitted with Uprated Ball Joints and SuperPro Bushes to reduce Arm movement Fixed offset upper control arms with heavy-duty, high-articulation ball joints and SuperPro polyurethane bushings for 1 to 3 inch lifted vehicles.The SuperPro fixed offset upper control arm (UCA) is a high-performance aftermarket component designed to enhance the wheel alignment of lifted 4x4 vehicles, resulting in reduced tire wear and improved overall performance. This UCA is constructed using high-strength steel forgings and tube steel, making it durable and reliable for heavy-duty use. The components are robot-welded, ensuring consistent and precise manufacturing standards.
The SuperPro fixed offset UCA features a heavy-duty high-articulation ball joint that enables the suspension to have greater articulation without binding, allowing for improved control and handling over rough terrain.
This UCA also includes SuperPro’s renowned polyurethane bushings, which offer superior resilience and durability compared to traditional rubber bushings. The polyurethane material is resistant to abrasion, wear, and chemicals, making it ideal for harsh off-road environments.
Vehicle Application Information: - Fitting Difficulty: difficult
- Fitting Position: Front
- Fitting time [min]: 180
- Axle alignment required after fitting
- Part of kit: KIT6690K (x1)
|
| Front | Control Arm Upper Inner Bush Kit
| SPF5490K | 1 | | $298.00 |
Mounting Kit, control/trailing arm mountingControl Arm Upper Inner Bush KitControl arm bushes stabilise the movement of the arms to ensure the correct geometry is maintained in all situations.
Worn or rubber bushes in these locations lead to dynamic changes in wheel alignment that effect the handling of a vehicle as well as the tyre life.
SuperPro Bushings solve this issue and are the perfect repair or repair upgrade solution. Vehicle Application Information: - Fitting time [min]: 180
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Part of kit: (x)
|
| Front | ReadyStrut Top Caps
| RS013 | 2 | | $102.00 |
Suspension Strut MountingReadyStrut Top CapsKit includes: Strut Cap, Spring Seat, Nuts & Washers Upgrade your suspension with our complete Bolt-In Replacement.
Featuring an Increased Durometer Spring Seat to prevent sag and increase durability, this product restores lost height from sagged rubber isolators, giving your vehicle a new lease on life.
Elevate your ride today! - Fitting Position: Front
- Fitting Difficulty: difficult
- Fitting time [min]: 60
- Part of kit: (x)
|
| Rear | 24mm Heavy Duty 3 Point Adjustable Sway Bar
| RC0121RZ-24 | 1 | | $373.00 |
Stabiliser Bar, suspension24mm Heavy Duty 3 Point Adjustable Sway BarIf you are looking for increased cornering capabilities with decreased body roll, Roll Control sway bars are the answer!
By being adjustable the Sway bar rates can be increased between 30-50% over OE sway bars by simply changing the end link position on the sway bar.
- Fitting Position: Rear
- Fitting Difficulty: difficult
- Fitting time [min]: 90
- Part of kit: (x)
|
| Rear | Panhard Rod - Adjustable
| TRC499 | 1 | | $287.00 |
Mounting, panhard rodPanhard Rod - AdjustableHeavy duty off-car adjustable - Fitting Position: Rear
- Fitting Difficulty: difficult
- Fitting time [min]: 60
- Part of kit: (x)
|
| Rear | Panhard Rod Bush Kit
| SPF2836K | 1 | | $124.00 |
Bush, panhard rodPanhard Rod Bush KitVehicle Application Information: - replaces both ends of the bar
- Fitting Position: Rear
- Fitting Difficulty: moderate
- Fitting time [min]: 120
- Fitting Difficulty: difficult
- Axle alignment required after fitting
- Fitting Position: Rear
- Fitting Difficulty: difficult
- Fitting time [min]: 120
- Part of kit: (x)
|
| Rear | Trailing Arm Lower - Adjustable Kit
| TRC497 | 1 | | $558.00 |
Control/Trailing Arm, wheel suspensionTrailing Arm Lower - Adjustable KitOff-car adjustable for pinion angle correction - Offroad use - Fitting time [min]: 60
- Fitting Position: Rear
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Part of kit: (x)
|
| Rear | Trailing Arm Lower Bush Kit
| SPF2461K | 2 | | $116.00 |
Mounting Kit, control/trailing arm mountingTrailing Arm Lower Bush KitVehicle Application Information: - this kit contains bushes to do either one complete arm, or both rear positions or both front positions
Vehicle Application Information: - Fitting time [min]: 210
- Fitting Position: Rear
- Fitting Difficulty: difficult
- Part of kit: (x)
|
| Rear | Trailing Arm Upper - Adjustable Kit
| TRC498 | 1 | | $488.00 |
Control/Trailing Arm, wheel suspensionTrailing Arm Upper - Adjustable KitOff-car adjustable for pinion angle correction: min 302mm to max 337mm - Fitting time [min]: 60
- Fitting Difficulty: difficult
- Fitting Position: Rear
- Axle alignment required after fitting
- Part of kit: (x)
|
| Rear | Trailing Arm Upper Bush Kit
| SPF5507K | 1 | | $93.00 |
Mounting Kit, control/trailing arm mountingTrailing Arm Upper Bush KitVehicle Application Information: - 2 kits required to do all bushings on both arms
Control arm bushes stabilise the movement of the arms to ensure the correct geometry is maintained in all situations. Worn or rubber bushes in these locations lead to dynamic changes in wheel alignment that effect the handling of a vehicle as well as the tyre life.
SuperPro Bushings solve this issue and are the perfect repair or repair upgrade solution. - Fitting Difficulty: difficult
- Fitting Position: Rear
- Axle alignment required after fitting
- Fitting time [min]: 100
- Part of kit: (x)
|
