Front | Control Arm Lower Assembly Kit Standard Replacement | TRC1078 | 1 |  | $306.36 |
 Control Arm/Trailing Arm, wheel suspensionControl Arm Lower Assembly KitStandard Replacement Left and Right Arms for Standard Replacement and Repair Upgrade Our front lower control arm kit for the Nissan X-Trail T32 has been designed to be an easy repair solution. Offering both alignment and vehicle handling improvements. Designed not just as a repair solution but as an upgrade! Supplied as a complete kit and fully assembled with special uprated ball joints and proprietary SuperPro bushings. We have made TRC1078 by far the best repair choice on the market. These arms utilise the SuperPro bushings and are manufactured from a high strength material. By eliminating the O.E style rubber bushing, these arms have been optimised for longevity, durability and performance, without any unwanted NVH. SuperPro Control Arms are perfectly suited as a standard replacement and are an upgrade from the factory arms, eliminating the undesirable arm movement to maintain better steering geometry in all driving conditions.
SuperPro Tip - SuperPro strongly advises that both arms should always be replaced at the same time to maintain the correct geometry and operation of the vehicle.- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Fitting Time [min.]: 120
- Part of kit: (x)
|
Front | Control Arm Lower-Inner Rear Bush Kit Standard replacement | SPF3452K | 1 |  | $195.84 |
Mounting Kit, control/trailing arm mountingControl Arm Lower-Inner Rear Bush KitStandard replacement - Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Fitting Time [min.]: 90
- Part of kit: (x)
|
Front | Control Arm Lower-Inner Rear Bush Kit - Double Offset Double caster offset, approx. 2 degree change | SPF3454K | 1 |  | $195.84 |
Mounting Kit, control/trailing arm mountingControl Arm Lower-Inner Rear Bush Kit - Double OffsetDouble caster offset, approx. 2 degree change A Double Offset kit is used for enhanced handling performance and will deliver positive caster to both sides of the vehicle. The vehicle will have improved directional stability, crisper, more responsive steering and improved 'return to centre' feel. This is a non tyre wearing geometry change that has a substantial effect on a vehicles handling characteristics.
Follow the installation instructions and enjoy the results! Vehicle Application Information: - Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Fitting Time [min.]: 90
- Part of kit: (x)
|
Front | Control Arm Lower-Inner Rear Bush Kit - Single Offset Single caster offset, approx. 1 degree change | SPF3453K | 1 |  | $195.84 |
Mounting Kit, control/trailing arm mountingControl Arm Lower-Inner Rear Bush Kit - Single OffsetSingle caster offset, approx. 1 degree change Use this kit to rectify a steering pull after a vehicle has been aligned to the manufacturers specifications.
Supplied with an offset bush to be fitted to the passenger side and a standard bush for the drivers side, these kits stagger the caster or setback by repositioning the ball joint slightly forward in the chassis.
This is a non tyre wearing geometry change that has a substantial effect on a vehicles ability to track straight and other handling characteristics.
Follow the installation instructions and the problem is solved. Vehicle Application Information: - Steering Pull Correction Kit
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Fitting Time [min.]: 90
- Part of kit: (x)
|
Front | Sway Bar Link LHS - Standard Replacement | TRC4036L | 1 |  | $42.32 |
Stabiliser Bar, chassisSway Bar LinkLHS - Standard Replacement 12mm Ball Joint Link
160 degree opposed
Length 300mm center to center - Fitting Difficulty: moderate
- Fitting Position: Front
- Fitting Time [min.]: 30
- Part of kit: (x)
|
Front | Sway Bar Link RHS - Standard Replacement | TRC4036R | 1 |  | $42.32 |
Stabiliser Bar, chassisSway Bar LinkRHS - Standard Replacement 12mm Ball Joint Link
160 degree opposed
Length 300mm center to center - Fitting Difficulty: moderate
- Fitting Position: Front
- Fitting Time [min.]: 30
- Part of kit: (x)
|